jumpToMain
Adapter cable with accessories (item no. 4.07360.53.0) | Pierburg | Motorservice

Adapter cable (4.07360.53.0) for current exhaust gas back pressure sensors

To replace previous versions

Pierburg | Motorservice
Back to search

Information on the product

Adapter cables for exhaust gas back pressure sensors make it easy to replace previous versions and improve vehicle performance. These cables are important for connecting to the differential pressure sensor, which monitors the exhaust gas back pressure (EGBP). Common problems such as errors in the fault code memory can mean a loss of power or inaccurate values. Correct connection to the control unit and correct supply are critical to reducing error codes.

Workshops should ensure that the adapter cables are suitable for injectors, boost pressure sensors and temperature feelers. Special attention must be paid to regenerating the particulate filter (for diesel = DPF) and the lambda sensor, as they are directly related to exhaust gas purification and efficiency. High-quality adapter cables are essential to optimise exhaust system performance and to keep emissions within legal limits.

Adapter cable with accessories (item no. 4.07360.53.0) | Pierburg | Motorservice
Adapter cable with accessories (item no. 4.07360.53.0)
The exhaust back pressure sensor with ref. no. 22 36 517 19R has been discontinued. This sensor was used in Renault engines. In some cases, the affected engines were also installed in Mercedes-Benz, Nissan and Dacia vehicles (see table on the back). As OE, the exhaust back pressure sensor has been replaced with a sensor that has a different connector plug. As a result, if this old, discontinued sensor fails, the original plug must be removed and replaced with a suitable one.
Exhaust back pressure sensor (item no. 7.12061.00.0) | Pierburg | Motorservice
Exhaust back pressure sensor (item no. 7.12061.00.0)
To make it easier to replace the part, Motorservice offers the adapter cable 4.07360.53.0, which enables the discontinued exhaust back pressure sensor to be easily replaced with the suitable model 7.12061.00.0 from Pierburg.

View of old plug

22 36 517 19R
22 36 517 19R  - View of old plug - Exhaust back pressure sensor | Pierburg | Motorservice
22 36 517 19R - View of old plug

View of new plug

7.12061.00.0
Exhaust back pressure sensor - 7.12061.00.0 - View of new plug | Pierburg | Motorservice
7.12061.00.0 - View of new plug

Exhaust back pressure sensor 7.12061.00.0

Pierburg no. Manufacturer (excerpt) Ref. no.
7.12061.00.0 Renault, Dacia 22 36 517 19R
Mercedes-Benz A 607 905 02 00
Nissan 22760-00Q0A

Adapter cable 4.07360.53.0

Pierburg no. Manufacturer (excerpt Ref. no.
4.07360.53.0 Renault, Dacia 82 01 428 503
Mercedes-Benz A 415 540 16 01
Nissan 24021-00QAA

Scope of supply for adapter cable 4.07360.53.0

The set for the adapter cable 4.07360.53.0 contains:
  • Cable with new plug (suitable for 7.12061.00.0)
  • 3 shrink-fit connectors

Conversion measure

  • Cut off the old sensor 223651719R close to the old plug.
  • Connect the adapter cable 4.07360.53.0 using the shrink-fit connectors, making sure to observe the pin assignment.
Conversion measure - Adapter cable for current exhaust gas back pressure sensors - To replace previous versions | Pierburg | Motorservice
Conversion measure

Pin assignment for exhaust back pressure sensor 7.12061.00.0 and adapter cable 4.07360.53.0

  1. Ground (red)
  2. Signal output (yellow)
  3. Supply voltage (black)
View of plug of adapter cable 4.07360.53.0 | Pierburg | Motorservice
View of plug of adapter cable 4.07360.53.0